Address

4175 S. Meridian Rd, 48637 Merrill, Michigan

Opens at 09:00 am

How to Pick a Camper Lock with a Bobby Pin

It is not entirely a good idea to get locked out of your camper.  Everything you can do to correct the issue must be done. 

At a time like this, you may need to call on a locksmith to help you open the lock so that you can gain entry again. However, it may take time for the locksmith to come around or the camper may be located in a remote area where it can be difficult for you to reach out to a locksmith.

When you find yourself in such a situation, you can as well look for an alternative solution to the problem. One of the best alternative solutions worthy of note involves the use of a bobby pin.   

With a bobby pin, you can get the door of the camper unlocked successfully, provided you know how to use it. The information provided here is focused on how to pick a camper lock with a bobby pin.

We will teach you how to do it so that you can be fully prepared for such an emergency. Follow the steps discussed below to successfully unlock your camper lock using a bobby pin.

Step 1

Straighten out the bobby pin

The first step on how to pick a camper lock with a bobby pin involves straightening out the bobby pin. This is very simple. All you have to do is to pull it apart and continue until it is turned into just a long, flat piece of metal.

Remove the rubber knobs you can find on the end of the bobby pin so that they will not get in the way when unlocking the camper.  Your teeth or a pair of cutters can be used for this purpose.

Step 2

Bend the pin to form a pick

You can use the lock for bending the tip of the pin to form a pick. You only need to stick the pin into the lock about 1 cm deep with the flat side facing up. Push the remaining to the left and the end of the pin a little bit until it curls a few millimeters.

How to Pick a Camper Lock with a Bobby PinImage Source: Wikihow

Before you can get it right, it may need to push the pin into the lock about 3 inches to the left.

Next, you need to bend one end of the picks until it forms a handle so that you can hold it conveniently during the lock picking process.   

The next thing on how to pick a camper lock with a bobby pin is to form a lever from the bobby pin and this can be done by bending it to a right angle.  You can use your finger to blend it right.  The lever will play the role of the key and turn the lock once the pin is moved.

Step 3

Understand how the lock works

Before you can proceed on how to pick a camper lock with a bobby pin, you need to first understand how the camper lock works.  Typically, a lock consists of two parts, which are the pins and barrel. 

The barrel acts as the chamber in which the lock is inserted.  The pins, on the other hand, are small cylinders made of metals sinking into the barrel and holding the barrel in place to enable you to push them out of the way.

All you want to do is to push the pins up into the correct position and then turn the barrel to fall back into place. The barrel will turn freely and the door will open immediately after you have gotten all the pins out of the way.

Step 4

Pick the lock

First of all, insert the lever you formed from the bobby pin into the bottom half of the lock. Then push the lever into the barrel as deeply as possible.  Make sure you keep the lever low all the time. 

Once the lever is very deep into the barrel, you can then turn the lock in the direction to open it.  You should handle the lever as if you are handling the key to the camper lock.  All you are interested in is applying adequate pressure to move the lock.  

While applying pressure, however, make sure the pressure is not too much so that the pin will not be trapped inside the barrel after you have unlocked the door.  

You can try turning it in both directions if you do not know exactly which direction the lock should turn.  If you turn it in the wrong direction, you will hear a grinding sound.

Next, insert the pick while bending it upward. Make sure that the pick touches the pin and move the two into the lock-in unison.  As you move the two into the keyhole. You will feel the pins moving and giving way to your pick.

You must bend the pick upward. The tension should not be too much so that the pins can move as you push the pick into the lock.

As the pick touches each of the pins, push it up until it clicks. Then, push the pick further into the lock to enable you to push the next pin upward. Continue doing this until you reach the last pin in the lock. 

The pick will act as the lever that pushes the pins up you also need to push the lever into the lock quickly immediately after successfully pushing up any of the pins in the lock.  A clicking sound after pushing up each pin indicates that you have successfully released

Aside from a camper lock, you can use the method we have described above on virtually any other lock and it will work effectively.

Conclusion

You can follow the steps we have described above if you are looking for how to pick a camper lock with a bobby pin. You may not get it right the first time, but you should keep at it and it will fall in place with consistent practice. 

To avoid mistakes while picking the lock, it is advisable to handle the lock picking slowly and steadily.  Bear in mind that more complicated locks may not respond to this unlocking method.        

Leave a Reply

Your email address will not be published.